When your Dyson air purifier displays an “F” code with three flashing bars, it indicates that the filter needs to be replaced. Dyson filters generally last around 12 months, so you can expect to see this code at least once a year.
However, the main issue with this code lies in the filter replacement process because many people aren’t familiar with the replacement procedure. So, this is what needs to be done: when you notice the “F” code with three bars, you must replace your air purifier’s old filter with a new one and RESET the filter reset indicator. Then, the “F” code will stop blinking, and that’s all.
The question is whether this code is the same on every Dyson air purifier and if the reset procedure is the same for all. Unfortunately, it’s not. But you can attempt to reset the Dyson filter reset indicator by holding your finger on the Power ON/OFF button on the remote controller of your Dyson for 6 seconds or simply do the procedure through the smart app.
What are other F codes on Dyson Air Purifiers?
If you are a Dyson air purifier owner, you will see the “F” code with three bars beside it on your device sooner or later.
As I mentioned before, this code informs you that it’s time to replace the filter. However, there are a few other F codes that can appear on your Dyson:
Dyson F1 Code
This code indicates a problem with the Piezoelectric charge. To resolve this issue, you need to turn off the air purifier and unplug it from the power source.
Then, wait for 60 seconds and turn it back on. If this process doesn’t work, try repeating it several times.
Dyson F2 Code
This message applies only to Dyson devices equipped with UV-C light and indicates an issue with the light emission. The repair procedure is the same as for the previous code message.
Turn off the air purifier, unplug it from the power source, and wait for 60 seconds before turning it back on. Repeat the process several times if the error persists.
If the code continues showing, it may be that the UV-C light needs replacement.
Dyson F3 Code
You’ll most typically get this code with Dyson humidifiers, but it can also appear with air purifiers. This code indicates that your machine is too cold.
The room temperature where you use the Dyson should not fall below 5°C (41°F). If the temperature drops below this value, you’ll receive the F3 error, and your Dyson will shut down, preventing you from turning it back on until you warm up the room to a higher temperature.
The reset procedure for this code is the same as for the previous ones. Turn off the device, unplug it from the power source, wait for 60 seconds, and turn it back on. Repeat the process several times, but make sure the room temperature is above 5°C (41°F).
Dyson F4 & F5 Codes
Dyson hasn’t provided clear explanations for these error codes, but the resolving procedure is identical to the previously described errors.
FAQ on Dyson Code “F”
In that case, you won’t be resetting the filter reset indicator but the WiFi indicator, which will typically light up in green after resetting it.
What is the easiest way to reset the filter reset indicator on Dyson?
The easiest way to reset the filter reset indicator on Dyson is by holding your finger on the Power ON/OFF button on the remote controller or through the Dyson smart application, which is available for Android and iOS devices.
For some Dyson air purifiers, mostly newer models, instead of the Power ON/OFF button, the procedure is a bit more challenging, requiring you to hold the oscillation button to reset carbon filters and the sleep mode button to reset particle filters.
Is the “F” code an error or just information?
Essentially, the “F” code is information indicating that the filter in your Dyson air purifier is dirty and needs replacement. It isn’t an error or an indication of a malfunction on your device.
Does every Dyson air purifier display the “F” code?
No, some Dyson air purifiers have a different display, which is more visually appealing. It usually presents a graphic illustration of a dirty filter in red color, with an exclamation mark above it.
Final Thoughts
When you notice an “F” code, with three bars beside it, on your Dyson air purifier, it is not a sign of any error but simply an indication that the filter is worn out and needs to be replaced as soon as possible.
After successfully replacing the filter and following Dyson’s recommended procedure, the final step is to reset the filter reset indicator, which will resolve the blinking “F” code or any other indicator indicating that it’s time to reset the filter.
If you have any questions about your Dyson air purifier, feel free to leave a comment in the comment box below. I will make an effort to respond to every comment as quickly as possible.
Hello, I have a Dyson HP01 and replaced the filter for the first time, I have pressed all kinds of buttons and combinations and I still can reset the F code with the lines on it, If I pressed the power button on the remote it will either power it of or power it down, if I press the power button on the unit itself it will increase the temperature and decrease it as well. Please assist?
For that model, you need to press and hold the night mode (sleep mode) button on your remote to reset the filter indicator (F code).
Where are your instructions to clear the F3 error message? Can you send them please?
I explained all the codes in the article.
The F3 error message indicates that your machine is too cold. To fix this issue, turn off the device, unplug it from the power source, wait for 60 seconds, and then turn it back on.
Milan, please help my Dyson Hot and Cold. It gives me an E8 when I switch to hot, not in the cold. It spins still. Can you please tell me how to fix it and what it needs? Thanks
You may need to reset your machine. To do this, switch it off and unplug it from the outlet for at least 30 seconds. Afterward, plug the machine back in and test it; the error code should be cleared.
My filter indicator will not reset. I’ve pressed the on/off button a million times after replacing the filter and turning it on first. Nothing happens. Is it malfunctioning or something. Super frustrated
What model do you have?
Thank you. Thanks to your instructions, I persevered and took 4 times of unplugging, waiting 60 seconds, and pressing for 6 seconds. I might have given up earlier had I not read this.
I’m glad the instructions in the article helped you!
Thank you so much for this article and the instructions. This is exactly what I needed. You’re a lifesaver!
I’m glad you find this article helpful.
Pressing the on/off button on my Dyson Fan has reset the Error message immediately. Thank you for the advice.
I’m glad to hear that.
Thanks for commenting!
Hold the on/off button and it should fix that. Mine did after I changed my filter
Thanks for the tip!
Just replaced hepa filter and still seeing the “F” light. WTH ?
Have you reset the filter reset indicator? You can do so by following my instructions.